March 16, 2020 0 Comments

CFGQ Silicon Labs 8-bit Microcontrollers – MCU 25 MHz 16 kB 8- bit MCU datasheet, inventory, & pricing. Explore the latest datasheets, compare past datasheet revisions, and confirm part lifecycle. CF datasheet, CF pdf, CF data sheet, datasheet, data sheet, pdf, Silicon Laboratories, Full Speed USB, 16k ISP FLASH MCU Family.

Author: Arazuru Faekus
Country: Russian Federation
Language: English (Spanish)
Genre: Photos
Published (Last): 21 October 2009
Pages: 411
PDF File Size: 6.8 Mb
ePub File Size: 6.39 Mb
ISBN: 886-7-80044-983-1
Downloads: 23321
Price: Free* [*Free Regsitration Required]
Uploader: Netaur

This bit sets the masking of External Interrupt 0. Silicon Labs Capacitive Touch Sense Touch sensitive switches are found in a variety of consumer products including home appliances, MP3 players and cell phones. This register serves as a second accumulator for certain arithmetic operations.

Ports are available as ADC inputs This bit sets the priority of the Timer 3 interrupt. In master mode, data on MISO is sampled.

In its default state, the ADC0 input is continuously tracked, except when a conversion is in progress. The minimum input adtasheet is 2. It returns to logic 0 when a data byte is transferred to the shift register from the transmit buffer or by a transition on SCK.

Unfortunatelly the pin layout is probably thought to be used with male type USB connectors datashdet by using mini-B female connectors I’m forced to do weird routing of the USB signals. Applies only to external oscillator sources. These little guys look really cool, I have to say, and I always shy ed away from core mcu’s because I thought they they are “archaic” and slow, not to mention that I don’t see as much of a community around them as with pic’s or Atmegas.


A No-Clean, Type-3 solder paste is recommended.

CF (ETC) PDF技术资料下载 CF 供应信息 IC Datasheet 数据表 (1/ 页)

HID uses Interrupt type endpoints, they can transport one report every bInterval ms. Writing a byte to SBUF0 initiates the transmission. I have EP1 c8501f320 64B when not double-buffered and 32B when double-buffered.

Email Required, but never datadheet. All dimensions shown are in millimeters mm unless otherwise noted. Tracking initiated on overflow of Timer 3 and lasts 3 SAR clocks, followed by conversion. Note that the shown response options are only the typical responses; application-specific dataaheet are datashheet as long as they conform to the SMBus specification Operate in slave mode.

The lower bytes of data memory are used for general purpose registers and scratch pad memory. If operating from the external oscillator, switch to the internal oscillator during Flash write or erase operations.

Bulk type endpoints allow much higher data throughput. Last reset was not a USB reset; Write: A divided version of the Multiplier output can also be used as the system clock. Master Datxsheet Device Device Figure If there is new information available in the receive buffer that has not been read, this bit will return to logic 0. Post as a guest Name.


Clear Data Toggle Write: Interrupt Register Descriptions The SFRs used to enable the interrupt sources and set their priority level are described below. Lost arbitration while attempting STOP. This bit mimics the instantaneous value that is present on the NSS port pin at the time that the register. Instruction and CPU Timing Global Electrical Characteristics Table 3.

C8051F320 PDF Datasheet浏览和下载

Refer to the datasheet section associated with a particular on-chip peripheral for information regarding valid interrupt conditions for the peripheral and the behavior of its interrupt-pending flag s Bias Current 3 Dropout Voltage Notes: By using our site, you acknowledge that you have read and understand our Cookie PolicyPrivacy Policyand our Terms of Service.

Comparator0 is shown in Figure 7.

All specifications apply to both Comparator0 and Comparator1 DD unless otherwise noted. Refer to Figure SI daasheet be cleared by software. RI0 flag is set. Comparator0 rising-edge interrupt disabled. IN Endpoint 2 Interrupt Enable 0: Each device is specified for 2.