EUROSEC PR5208 MANUAL PDF

June 26, 2020 0 Comments

Throughout this manual refer- ence will be made to the User Code, the factory set default is This code is programmable along with eight other User Codes. The eurosec control panel is supplied as a blank fronted end station . Wire the LCD RKP as shown in the wiring section of this manual. View and Download Eurosec CP8L user manual online. LCD. CP8L Control Panel pdf manual download.

Author: Goltilar Ducage
Country: Cuba
Language: English (Spanish)
Genre: Photos
Published (Last): 17 September 2014
Pages: 271
PDF File Size: 9.23 Mb
ePub File Size: 5.85 Mb
ISBN: 644-4-71477-168-2
Downloads: 17945
Price: Free* [*Free Regsitration Required]
Uploader: Gorr

Introduction Welcome to the eurosec control panel. Your installation company will have programmed your system to protect your premises to the highest possible standards.

Eurosec CP8L User Manual

Several user programmable options are available that will be covered later in this manual. Throughout this manual, reference will be made to the Master User Code, the factory set default is Display Status Blanking Depending on Control Panel installed, it may be a requirement that the Status Eurosce or Unset display of the security system is not displayed.

Set or Unset Status will only be displayed for ten seconds when the system is Set or Unset.

The bottom line of the display will then be blanked off. Full Setting the System. Two methods are available for Full Set. After checking the premises are secure: Enter a valid User Code followed by. The exit tone will now sound. Exit the premises via an authorised exit route.

At the start of the setting procedure, a fault Exit Now! The display will show, for example: Part Setting the System using Part 2 or 3. Two other Part Sets may be available for your system.

Part 2 is a second set of zones that may be omitted and Part 3 will combine Part 1 and Part 2. To use Part 2 or 3. Enter a valid User Code followed by 2 or 3. Enter the premises via an authorised Entry Point. The entry tone will sound. Proceed to the keypad and enter a valid User Code.

Display After an Alarm. If an alarm occurs when the system is set, the cause of the alarm will be displayed for 10 seconds after you unset the system.

Resetting After an Alarm After an alarm the system needs to be reset. Your installation company will have programmed the reset modes for your system so that it complies with your insurance company and legislation requirements. Your installation company will have informed you as to the type of reset that your system is set for.

  CAROLINA SE ENAMORA FEDERICO MOCCIA DESCARGAR PDF

If a Master Code Reset has been programmed by the engineer, a higher level of code will be required. If Alarm Reset has been programmed for Master, then the display will show, for example, each time the User attempts to set! If Anti has been programmed for Alarm Reset, contact the Central Station or Engineer, as instructed by the Installation Company and quote the number given by the display.

Tamper Resetting With the display showing: Enter a valid User code.

The system is now reset. Setting the system with Mains Fail In the event of a short term power cut, where it is known when power will be restored, e.

Enter your User Code again followed by. Pressing the Quick key during exit will shorten the exit time to 3 seconds. Re-setting the display after a Mains Fail If the system has been programmed for Any nanual reset; With the display showing: Enter your User code Then press Reset.

The display is now reset. Programming User Codes Up to nine user codes may be programmed on predetermined levels. User Numbers 1 to 3 Master Level.

EUROSEC CP8L USER MANUAL Pdf Download.

User Numbers 4 to 7 User Level. Allows Set, Part Set and Unset. User Numbers 8 to 9 Set Only Level. Do You Want to. The display will show: The display will show for example: Text is entered in a similar way that you would enter text on a mobile telephone. Select characters from the list below: Continue until you have entered eight characters. Programmable User Options Several user programmable options are available via user codes 1, 2 or 3. To use these options please follow instructions below.

Delete Zone Option This option allows individual zones to be deleted omitted when the system is being set. Zone delete is only effective for one Set and will need to be repeated for subsequent Sets. Walk around the area being tested. As each device is manuual there will a tone from the internal sounders and the display will show the triggered circuit.

To test the bells external sounders and strobe press 9. To stop the bell test press 9 again. To escape back to Unset press 0 three times. Enter the time using the 24 Hour clock e. The display will show, 03 Jul Press Yes to accept. To return to the Unset Mode press 0 twice.

  DEMON IN MY VIEW BY AMELIA ATWATER-RHODES PDF

To return to the Unset Mode press 0 eurisec times. EN control panel only. The the log may store up to events with time and date stamp.

Non EN control panel. Maual on the Log mode Note: System Details Installation By: Page of 28 Go. Table of Contents Add to my manuals Add. Table Of Contents Contents Introduction Introduction Introduction Welcome to the eurosec control panel. Unsetting The System Unsetting the System. Page 10 If a Master Code Reset has been programmed by the engineer, a higher level of code will be required. Page 13 Enter your User Code again followed by. Page 16 Press No. Page 17 Text is entered in a similar way that you would enter text on a mobile telephone.

Programmable User Options Programmable User Options Several user programmable options are available via user codes 1, 2 or 3. System Test Press 0 twice. Page 22 Enter the time using the 24 Hour clock e.

Keypad Alert To return to the Unset Mode press 0 three times. Page 28 Installed By: Comments to this Manuals Your Name. Enter text from picture: Recently I had mains fault come on pad and entered code to reset, all that then happened was the alarm went off again, so I googled the issue and it seemed it was possibly the battery that needed changing, do I bought a new battery, fitted it and now 4 days later this morning alarm went off again and says mains fault Is there something I am missing or need to do?

Had a power pg5208 to house for two –thee hours now I can not set the alarm On the Eurosec. Can the volume on the control panel be turned down.

When set on ‘panel’ in the evening it is lengthy and quite loud. Thank you for publishing this alarm Manuel. How do I st the door chime for when people enter the house, while Eurossc am still at home? By pressing ‘print’ button you will print only current page. To print the manual completely, please, download it. Don’t show me this message again. Got it, continue to print. Don’t have an account?