March 13, 2020 0 Comments

I would like to get a very nice trigger job on a SS GP for the single Ruger forum I found the IBOK for the GP on Google (GP IBOK). I received the GP pdf this morning. I found the IBOK so helpful thought I should bump it back up so others could keep seeing it. Gp Ibok – PDF Free. Download – -. Ruger sp manual pdf ruger sp manual pdf magnum revolver like the. Ruger GP For many.

Author: Kaziktilar Akinos
Country: Dominican Republic
Language: English (Spanish)
Genre: Photos
Published (Last): 8 December 2012
Pages: 34
PDF File Size: 2.52 Mb
ePub File Size: 4.12 Mb
ISBN: 737-6-60524-720-5
Downloads: 42580
Price: Free* [*Free Regsitration Required]
Uploader: Gardanris

Use a hollow shaft flat tip screwdriver and unscrew left hand thread the ejector retainer part iibok I hope you enjoy the rest of the blog. Thu Dec 06, Do not try to drill any deeper, just get the hole smooth.

I’ve taken every last spring, screw and lost-in-the-carpet-sized pin out of every gun I’ve ever owned. If I tipped it up, the hammer worked, down, no hammer.

Aside from the overly heavy mainspring in the revolvers, these problems are just a matter of Ruger not using rigorous statistical quality control methods, which have been a standard engineering production process for 50 years in manufacturing precision mechanical devices.

Remove any galls and clean the channels inside the frame.

Strange problem with my GP100

It happened again, after approx. You can still shoot jacketed bullets with near-equal performance to the factory set up. Place endshake bearing s on the ibbok tube and insert the crane into the cylinder.

To remove the grips, unscrew the grip screw part 19 most of the way out then push on the head of the screw to dislodge the left grip panel part tp100 If the latch binds, you will have to locate the bind and dress the frame or crane latch.


The endshake bearings are nothing more than washers. I love that gun. A very nice contribution to the hobby of shooting.

Glad to see the IBOK is still available online. This can ibk measured by laying gap gauge blades on the recoil shield and ibpk protrusion to thickness. Remove the pawl spring and plunger. It’s myif I could only have one gungun. If it is too short, a new one will have to be fitted and installed at the Ruger factory. The FFL offered to send it back but I persevered and got it apart. If the hammer pushes off, you will need to repair the sear or replace the hammer part 64 or trigger part Lay the sight in position and push the sight pivot pin into the hole and through the sight until it is flush on both g1p00.

I knew I wouldn’t want to get rid of the GP before, but now it’s going to be a joy to shoot and I’m positive I’ll never want to get rid of it. Place the front dovetail of the sight in the channel. A worn or out of spec trigger plunger part 48 or cylinder latch part 6 will cause late initial timing.

This has two major advantages. Bottom line is that Ruger makes good revolvers that are build to last and work well out of the box. You want the longer one. A fine file will work well inok remove burrs or high spots.


GP IBOK for SP – Ruger Forum

Been a long time since I busted one of these puppies apart, nice to have a reference to check. I wont go anywhere near the trigger on it as it’s damn smooth already. A good gpp100 is a 12 lb mainspring. It’s incredibly comprehensive and extremely helpful for understanding how everything works! The factory mainspring is rated at 14 lbs.

Remove the latch plunger part 30 and the spring part 8 from the trigger guard assembly. This will cause a bind in DA trigger pull or a hard start cocking for SA. Place your left index finger in the trigger guard behind the trigger. Can anyone help me I need a complete trigger or all parts to fix my gp please tell me where to find them. Firing pin strikes the primer causing the gun to fire. Use a Dremmel Tool with a buffing wheel and fine grit compound to dress the lower rear surface of the hammer dog.

If initial timing is slow, the cylinder will try to rotate before it is released. I bought one from a friend that was a week old for Mon Dec 03, 6: I’ve been shooting 9mm and.

These raised lines will not allow the cartridges to seat properly and will cause them to drag on the recoil shield. Find all posts by TrysteofFate. If I missed the reference my appologies.