ISO 7919-3 PDF
ISO MECHANICAL VIBRATION – EVALUATION OF MACHINE VIBRATION BY MEASUREMENTS ON ROTATING SHAFTS – PART 3: COUPLED . Mechanical vibration – Evaluation of machine vibration by measurements on rotating shafts – Part 3: Coupled industrial machines (ISO. Full text of “IS/ISO Mechanical vibration – evaluation of machine vibration by measurements on rotating shafts, Part 3: Coupled Industrial Machines”.
|Published (Last):||1 September 2005|
|PDF File Size:||9.28 Mb|
|ePub File Size:||11.52 Mb|
|Price:||Free* [*Free Regsitration Required]|
Certain terminology and conventions are, however, not identical to those used in Indian Standards. Search the history of over ido web pages on the Internet. These guidelines are presented in terms of both steady running vibration and any amplitude changes which can occur in these steady values. If the steady-state baseline changes for example, after a machine overhaulthe ALARM setting should be revised accordingly.
However, for those machines for which continuous monitoring of vibration is employed, it is common practice to establish operational vibration limits. Therefore, in certain cases the shaft displacement limits given in this part of ISO may exceed the available clearance. The values used will, therefore, generally be the same for all machines of similar design and would not normally be related to the steady-state baseline value used for setting ALARMS.
Hence, the specification of detailed criteria for measurements of this type is beyond the scope of this part of ISO MED 28 1 The criteria are presented for the specified steady-state operating conditions at the rated speed and load ranges. Specifications like the ISO spec you site are going to be 791-3 in nature since the construction of a machine may have considerable affect on its behavior.
79193- vibration – evaluation of machine vibration by measurements on rotating shafts, Part 3: Consequently, it can be difficult to identify the effects of the crack propagation by looking at the change in the broad-band vibration only.
In general, if an ALARM sio occurs, operation can continue for a period whilst investigations are carried out to identify the reason for the change in vibration and define any remedial action. Block When you block a person, they can no longer invite you to a private message or post to your profile wall. Y 90 80 70 7919- 50 40 30 20 10 a! For monitoring purposes the measuring system shall be capable of covering overall vibration up to a frequency equivalent to 2,5 times the maximum service speed.
In certain cases, there can be specific features associated with a particular machine, which would require different zone boundary values lower or higher to be used.
Various BSI electronic information services are also available which give details on all its products and services. However, they provide guidelines for ensuring that gross deficiencies or unrealistic requirements are avoided.
Machines with vibration within this zone are normally considered unsatisfactory for long-term continuous operation. It is the constant aim is BSI to improve the quality of our products and services. Draft International Standards adopted by the technical committees isk circulated to the member bodies for voting.
In industrial machines, shaft vibration relative to the bearing is normally measured.
izo For example, the propagation of a crack in a rotor can introduce a progressive change in vibration components at multiples of rotational frequency, but their magnitude might be small relative to the amplitude of iwo once-per- revolution rotational frequency component. In these cases alternative criteria are necessary.
It presents the UK view on standards in Europe and at the international level. This does not preclude the free use, in course of imple- menting the standard, of necessary details, such as symbols and sizes, type or grade designations.
Change in vibration magnitude This criterion provides an assessment of a change in vibration magnitude from a previously established reference or baseline value for particular steady-state conditions. Copyright BIS has the copyright of all its publications. Machines with vibration within this zone are normally considered acceptable for unrestricted long- term operation.
For undated references, the latest edition of the referenced document including any amendments applies. The corresponding Indian Standard which is to be substituted in its place is listed below along with its degree of equivalence for the edition indicated: Manage Follow Preferences Loading ISOMechanical vibration of non-reciprocating machines — Measurements on rotating shafts and evaluation criteria — Part 1: A list of organizations represented on this committee can be obtained on request to its secretary.
The work of preparing International Standards is normally carried out through ISO technical committees. You must be signed in to continue. The vibration magnitude is the higher value of the peak-to-peak displacement measured in two selected orthogonal measurement directions. The numerical values specified are not intended to serve as the only basis for vibration evaluation since, in general, the vibratory condition of a machine is assessed by consideration of both the shaft vibration and the associated structural vibration.
A significant increase or decrease in shaft vibration magnitude can occur which would require some action even though zone C of Criterion I has not been reached. Except as permitted under the Copyright, Designs and Patents Act no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means — electronic, photocopying, recording or otherwise — without prior written permission from BSI.
ISO | AMP Maintenance Forums
Users are responsible for its correct application. However, it should be noted that for diagnostic purposes it might be desirable to cover a wider frequency range. John from PA posted:. Vibration values within this zone are normally considered to be isl sufficient severity to cause damage to the machine. However, they provide guidelines for ensuring that gross deficiencies or unrealistic requirements are avoided.
The values chosen will normally be set relative to a baseline value determined from experience for the measurement position or direction for that particular machine.
ISO 7919-3 | AMP Maintenance Forums
Generally, the machine may be operated for a limited period in this condition until a suitable opportunity arises for remedial action. Change in vibration magnitude This criterion provides an assessment of a change in ios magnitude from a previously established reference or baseline value for particular steady-state conditions. Consequently, it can be difficult to identify the effects of the crack propagation by looking at the change in the broad-band vibration only.
For example, the propagation of a crack in a rotor can introduce a progressive change in vibration components at multiples of rotational frequency, but their magnitude might be small relative to the amplitude of the once-per- revolution rotational frequency component.
It should be noted that overall judgement of the vibratory state of a machine is often made on the basis of both shaft relative vibration io defined above and of measurements made on non-rotating parts see ISO . These values are not intended to serve as acceptance specifications, which shall be subject to agreement between the machine manufacturer and the customer.
Like Reply 0 Likes.